View LC420WU5-SLA2_4563098.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

product specification 1 /32 lc420wu5 ver1.0 42.0 wuxga tft lcd title model general buyer *when you obtain standard approval, please use the above model name without suffix lc420wu5 *model sla2(rohs verified) suffix lg.philips lcd co., ltd. supplier for approval specification tv product development dept. lg. philips lcd co., ltd d.k. yang / engineer prepared by reviewed by signature date approved by please return 1 copy for your confirmation with your signature and comments. / / / signature date approved by ) ) ( ( final specification preliminary specification j.h. yoon /senior manager j.t. kim / manager www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 2 /32 lc420wu5 ver1.0 contents 26 handling precautions for protection film 9-6 27~31 appendix 10 signal timing specifications 3-3 25 precautions 9 25 mounting precautions 9-1 25 operating precautions 9-2 26 electrostatic discharge control 9-3 26 precautions for strong light exposure 9-4 26 storage 9-5 12 8 interface connections 3-2 color data reference 3-5 24 designation of lot mark 8-1 24 packing form 8-2 24 packing 8 23 emc 7-2 1 cover 2 contents 3 record of revisions 4 general description 1 5 absolute maximum ratings 2 6 electrical specifications 3 6 electrical characteristics 3-1 11 signal timing waveforms 3-4 13 power sequence 3-6 15 optical specifications 4 19 mechanical characteristics 5 22 reliability 6 23 international standards 7 23 safety 7-1 page item number www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 3 /32 lc420wu5 ver1.0 final specification july, 27, 2007 1.0 description page revision date revision no. record of revisions www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 4 /32 lc420wu5 ver1.0 general features 1. general description cn1 (51pin) lvds 2port source driver circuit tft - lcd panel (1920 rgb 1080 pixels) g1 s1 s1920 g1080 mini-lvds(rgb) timing controller [lvds rx + dcr + odc integrated] gate driver circuit eeprom power circuit block sda scl +12.0v sdram mem ctrl rgb dcr enable vbr_out back light assembly 3pinx1cn(high) 3pinx1cn(high) +24.0v, gnd, vbr-a, vbr-b status inverter(master) inverter(slave) +24.0v, gnd viewing angle free ( r/l 178 (typ.), u/d 178 (typ.) ) viewing angle (cr>10) 8-bit, 16.7 m colors color depth 1920 horiz. by 1080 vert. pixels, rgb stripe arrang ement pixel format 500 cd/m 2 (center 1point ,typ.) luminance, white total 168.8 w (typ.) (logic = 8.8 w, inverter = 160 w [vbr-a=1.65v] ) power consumption 11.5kg (typ.) weight transmissive mode, normally black display mode hard coating(3h), anti-glare treatment of the front polarizer (haze 13%) surface treatment 0.4845 mm x 0.4845 mm pixel pitch 983.0(h) x 576.0 (v) x 51.0 mm(d) (typ.) outline dimension 42.02 inches(1067.31mm) diagonal active screen size the lc420wu5 is a color active matrix liquid crysta l display with an integral external electrode fluor escent lamp(eefl) backlight system. the matrix employs a-s i thin film transistor as the active element. it is a transmissive display type which is operatin g in the normally black mode. it has a 42.02 inch diagonally measured active display area with wuxga resolution (1080 vertical by 1920 horizontal pixel array). each pixel is divided into red, green and blue sub- pixels or dots which are arrayed in vertical stripe s. gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for ea ch dot. therefore, it can present a palette of more than 16 .7m(true) colors. it has been designed to apply the 8-bit 2-port lvds interface. it is intended to support lcd tv, pctv where high b rightness, super wide viewing angle, high color gam ut, high color depth and fast response time are importa nt. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 5 /32 lc420wu5 ver1.0 notes : 1. temperature and relative humidity rang e are shown in the figure below. wet bulb temperature should be 39 c max, and no condensation. 2. gravity mura can be guaranteed under 40 condition . 3. abnormal visual problems by panel front side sur face temperature can be occurred in specific range (60 c ~ 65 c), but materials (exp : polarizer) are not damaged permanently in this range, tsur. the following items are maximum values which, if ex ceeded, may cause faulty operation or damage to the lcd module. table 1. absolute maximum ratings 2. absolute maximum ratings v dc +5.0 0 v br brightness control voltage note 1,2 c +50 0 t op operating temperature v dc +27.0 +21.6 v bl backlight inverter lcm unit %rh 90 10 h op operating ambient humidity %rh 90 10 h st storage humidity c +60 -20 t st storage temperature v dc +5. 5 -0.3 von/off on/off control voltage at 25 2 c v dc +14.0 +8.0 v lcd power input voltage max min parameter remark value symbol 90% 10 20 30 40 50 60 70 80 0 -20 0 10 20 30 40 50 dry bulb temperature [ c ] wet bulb temperature [ c ] storage operation humidity [(%)rh] 10% 40% 60% 60 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 6 /32 lc420wu5 ver1.0 it requires two power inputs. one is employed to po wer for the lcd circuit. the other is used for the eefl backlight and inverter circuit. table 2. electrical characteristics notes : 1. the specified current and power consumpt ion are under the v lcd =12.0v, 25 2 c, f v =60hz condition whereas mosaic pattern(8 x 6) is displaye d and f v is the frame frequency. 2. the current is specified at the maximum current pattern. 3. the duration of rush current is about 2ms and ri sing time of power input is 1ms (min) mosaic pattern(8 x 6) white : 255gray black : 0gray 3. electrical specifications 3-1. electrical characteristics 1 ma 954 734 - 1 watt 11.48 8.8 - p lcd power consumption 3 a 3 - - i rush rush current v dc 12.6 12.0 11.4 v lcd power input voltage 2 ma 1125 866 - i lcd power input current circuit : parameter symbol max typ min note unit value www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 7 /32 lc420wu5 ver1.0 table 3. electrical characteristics (continue) power consumption ibl_b before aging ibl_a after aging power supply input current 5 hrs 50,000 life time 4 min 3 ts discharge stabilization time brightness adjust v br-a = 3.3v 2 a 8.5 8 - v br-a = 3.3v 1 a 8 7.5 - v br-a = 1.65v 1 w 172 160 - pbl v br-a = 1.65v 1 a 7.2 6.7 - 1 vp-p 0.5 - - power supply input voltage ripple v br-a = 1.65v 2 a 7.7 7.2 - 1 v bl = 22.8v v br-b = 3.3v v br-a = 1.65v a 9.6 - - irush power supply input current (in-rush) 3 v 3.3 - 0 v br-b lamp: inverter : vdc 3.3 1.65 0.0 v br-a brightness adjust input voltage for control system signals vdc 25.2 24.0 22.8 vbl power supply input voltage on/off off on vdc 5.0 - 2.5 v on vdc 0.8 0.0 -0.3 v off parameter symbol max typ min notes unit values notes : 1. electrical characteristics are determined after the unit has been on and stable for approximately 120 minutes at 25 2 c. the specified current and power consumption are under the typical supply input voltage 24vand v br (v br-a : 1.65v & v br-b :3.3v), it is total power consumption. the ripple voltage of the power supply input voltag e is under 0.5 vp-p. lpl recommend input voltage is 24.0v 5%. 2. electrical characteristics are determined within 30 minutes at 25 2 c. the specified currents are under the typical supply input voltage 24v. 3. the brightness of the lamp after lighted for 5mi nutes is defined as 100%. ts is the time required for the brightness of the c enter of the lamp to be not less than 95% at typica l current. the screen of lcd module may be partially dark by t he time the brightness of lamp is stable after tur n on. 4. specified values are for a single lamp which is aligned horizontally. the life time is determined as the time which lumin ance of the lamp is 50% compared to that of initial value at the typical lamp current (vbr-a : 1.65v & vbr-b :3.3v), on condition of continuous operating at 25 ? 2 c 5. the duration of rush current is about tbdms. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 8 /32 lc420wu5 ver1.0 table 4. module connector(cn1) pin configuration - lcd connector(cn1): fi-r51s-hf(manufactured by jae ) or kn25-51p-0.5sh(manufactured by hirose) - mating connector : fi-r51hl(jae) or compatible this lcd module employs two kinds of interface conn ection, a 51-pin connector is used for the module electronics and master 14-pin and slave 12-pin conn ectors are used for the integral backlight system. 3-2-1. lcd module 3-2. interface connections notes : 1. the pin no 44 is lcd test option. agp (auto gen eration lcm operates pattern) or nsb (no signal black) is case that lvds signals are out of frequen cy or abnormal condition in spite of 12 volt power supply. lpl recommends nsb. ( agp : vcc or ope n / nsb : gnd ) 2. all gnd(ground) pins should be connected togethe r to the lcd modules metal frame. 3. all vlcd (power input) pins should be connected together. 4. all input levels of lvds signals are based on th e iea 664 standard. 5. specific pins(pin no. #1~#10) are used for inter nal data process of the lcd module. if not used, these pins are no connection. 6. if dcr function should be enable(h), 10th pin must be connected to serial resistor which value is under 1k ohm. - 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 no - power supply +12.0v power supply +12.0v power supply +12.0v power supply +12.0v no connection ground ground ground no connection or gnd no connection or gnd no connection no connection second channel 3+ second channel 3- ground second clock channel c+ second clock channel c- ground second channel 2+ second channel 2- second channel 1+ second channel 1- second channel 0+ second channel 0- no connection or gnd description - vlcd vlcd vlcd vlcd nc gnd gnd gnd reserved reserved reserved (nc) reserved (nc) re3p re3n gnd reclkp reclkn gnd re2p re2n re1p re1n re0p re0n reserved symbol no connection reserved (nc) 25 no connection reserved (nc) 24 first channel 3+ ro3p 23 first channel 3- ro3n 22 ground gnd 21 first channel 1+ ro1p 15 first channel 1- ro1n 14 first channel 0+ ro0p 13 first channel 0- ro0n 12 ground gnd 11 no connection nc 2 no connection nc 3 no connection nc 4 no connection nc 5 no connection nc 6 h =jeida , l = vesa lvds select 7 external vbr vbr_ext 8 vbr output vbr_out 9 h = enable , l = disable dcr_enable 10 first channel 2- ro2n 16 first channel 2+ ro2p 17 ground gnd 18 first clock channel c- roclkn 19 first clock channel c+ roclkp 20 no connection or gnd reserved 26 description symbol no gnd ground 1 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 9 /32 lc420wu5 ver1.0 master -inverter connector : s14b-ph-smc (jst) or equivalent - mating connector : phr-14 or equivalent table 5. inverter connector pin configulation 3-2-2. backlight inverter rear view of lcm pcb pcb 14 1 1 12 slave -inverter connector : s12b-ph-smc (jst) or equivalent -mating connector : phr-12 or equivalent 2, 3 dont care v br-a analog dimming voltage dc 0.0v ~ 3.3v (typ : 1.65v) v br- a 11 dont care on/off 0.0v ~ 5.0v v on/off 12 4 - status normal : upper 3.0v abnormal : under 0.7v status 14 - gnd gnd gnd gnd gnd v bl v bl v bl v bl v bl slave v br - b gnd gnd gnd gnd gnd v bl v bl v bl v bl v bl master 3 backlight ground gnd 7 backlight ground gnd 8 1 burst dimming voltage dc 0.0v ~ 3.3v v br -b 13 backlight ground gnd 10 backlight ground gnd 9 backlight ground gnd 6 power supply +24.0v v bl 5 power supply +24.0v v bl 4 power supply +24.0v v bl 3 power supply +24.0v v bl 2 power supply +24.0v v bl 1 note description symbol pin no notes : 1. gnd should be connected to the lcd mod ules metal frame. 2. if pin #11 is open, v br -a = 1.65v. when apply over 1.65v( ~ 3.3v) contin uously, its luminance is increasing however lamps life tim e is decreasing. it could be usable for boost up luminance when usin g dcr (=dynamic contrast ratio) function only. 3. minimum brightness : v br -b =0v maximum brightness : v br -b = 3.3v 4. even though pin #14 is open, there is no effect o n inverter operating, the output terminal of inver ter. 5. each impedance of pin #11,12 and 13 is 112[ ? ], [ ? ], 112[ ? ] www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 10 /32 lc420wu5 ver1.0 table 6. timing table for ntsc (de only mode) table 6 shows the signal timing required at the inp ut of the lvds transmitter. all of the interface s ignal timing should be satisfied with the following specificatio n for normal operation. 3-3. signal timing specifications horizontal vertical lines 68 45 12 t vb blank lines - 1080 - t vv display period lines 1148 1125 1092 t vp total total blank display period t hp t hb t hv symbol 2200/2 tclk 1280 1100 1072 tclk 320 140 112 tclk - 960 - note unit max typ min item frequency vertical horizontal dclk f v f h f clk symbol hz 63 60 57 khz 68.9 67.5 65.5 148.5/2 mhz 77 74.25 71.55 note unit max typ min item table 7. timing table for pal (de only mode) note : the input of hsync & vsync signal does not h ave an effect on normal operation(de only mode). the performance of the electro-optical characterist ics may be influenced by variance of the vertical r efresh rate. table 7 shows the signal timing required at the inp ut of the lvds transmitter. all of the interface s ignal timing should be satisfied with the following specificatio n for normal operation. horizontal vertical lines 65 45 25 t vb blank lines - 1080 - t vv display period lines 1145 1125 1105 t vp total total blank display period t hp t hb t hv symbol 2200/2 tclk 1200 1100 1072 tclk 240 140 112 tclk - 960 - note unit max typ min item frequency vertical horizontal dclk f v f h f clk symbol hz 53 50 47 khz 57.25 56.25 55.25 123.75/2 mhz 65.6 61.88 58.3 note unit max typ min item www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 11 /32 lc420wu5 ver1.0 0.7vdd 0.3vdd t clk invalid data valid data invalid data invalid data invalid data pixel 0,0 pixel 2,0 pixel 1,0 pixel 3,0 de(data enable) valid data 0.5 vdd t hp t hbp t hv t hfp t vp t wv t vbp t vv t vfp hsync vsync de(data enable) de(data enable) dclk first data second data de, data t wh 3-4. signal timing waveforms * reference : sync. relation * t hb = t hfp + t wh +t hbp * t vb = t vfp + t wv +t vbp www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 12 /32 lc420wu5 ver1.0 the brightness of each primary color(red,green,blue ) is based on the 8-bit gray scale data input for th e color. the higher binary input, the brighter the color. ta ble 8 provides a reference for color versus data in put. table 8. color data reference 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 green (000) dark green 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 green (001) ... ... ... ... 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 green (254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 green (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 red (000) dark red 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 red (001) ... ... ... ... 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 red (254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 red (255) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (001) ... ... ... ... 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (254) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue (255) blue (000) dark white yellow magenta cyan blue (255) green (255) red (255) black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 basic color 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 blue msb lsb green msb lsb red msb lsb b7 b6 b5 b4 b3 b2 b1 b0 g7 g6 g5 g4 g3 g2 g1 g0 r7 r6 r5 r4 r3 r2 r1 r0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 blue color input color data 3-5. color data reference www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 13 /32 lc420wu5 ver1.0 3-6. power sequence note : 1. please avoid floating state of interface signal at invalid period. 2. when the interface signal is invalid, be sure to pull down the power supply v lcd to 0v. 3. the case when the t2/t5 exceed 3x(1/fv), it oper ates protection pattern (black pattern) till valid signal inputted. there is no reliability problem. ( ex. 60hz : 3x(1/60hz) = 50ms) 4. the t3/t4 is recommended value, the case when fa iled to meet a minimum specification, abnormal display would be shown. there is no reliab ility problem. 5. if the on time of signals(interface signal and o ption signals) precedes the on time of power(v lcd ), check the lcd logic power(vcc) is under 0.8v, other wise it will be happened abnormal display. 6. t6 should be measured after the module has been f ully discharged between power off and on period. t5 t2 - - 5 5 2,6 3,5 4 4 3,5 notes s - - 2.0 t6 ms 0 t8 ms 0 t7 ms 3 x (1/ f v ) - 0.5 t2 ms ms - - 200 t3 - - 200 t4 ms - - 0 t5 ms 20 - 0.5 t1 max typ min unit value parameter table 9. power sequence interface signal (tx) power for lamp power supply for lcd v lcd 10% 0v 90% 10% t 1 t 2 t 5 t 6 t 3 t 4 valid data lamp on t 7 t 8 option signal (lvds_select, dcr_enable, bit_select) 90% 3-6-1. lcd driving circuit www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 14 /32 lc420wu5 ver1.0 3-6-2. sequence for inverter power supply for inverter v on/off v bl 10% 0v 90% t 1 t 2 t 3 t 2 0.7v t 4 24v (typ.) t 5 lamp on t 4 t7 1000ms (min) 1000ms (min) table 10. power sequence for inverter 3-6-3. deep condition for inverter v bl (typ.) x 0.8 0 v v bl : 24v t6 notes : 1. t1 describes rising time of 0v to 24v an d this parameter does not applied at restarting tim e. 2. t4(max) is less than t2. 3. in t7 section, vbr-b is recommended 3.3v. v bl (typ) x 0.8 ms 10 - - t6 3 ms - - 1000 t7 - ms - - 10 t5 2 ms 0 t4 1 remarks ms - - 500 t2 ms - - 200 t3 ms - - 20 t1 max typ min units values parameter v br-a & v br-b www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 15 /32 lc420wu5 ver1.0 lcd module optical stage(x,y) pritchard 880 or equivalent 50cm fig. 1 optical characteristic measurement equipment and method optical characteristics are determined after the un it has been on and stable in a dark environment at 25 2 c. the values specified are at an approximate distance 50cm from the lcd surface at a viewing angle of and equal to 0 . fig. 1 shows additional information concerning the measurement equipment and method. 4. optical specification table 11. optical characteristics ta= 25 2 c , v lcd =12.0v, f v =60hz, dclk=148.5mhz vbr_a=1.65v, vbr_b=3.3v 3 1.3 - - 5p white 1 - 1000 700 cr gray-to-gray - - - 7 gray scale y axis, down ( =270 ) y axis, up ( =90 ) x axis, left ( =180 ) x axis, right( =0 ) - - 89 d - - 89 u - - 89 l 6 degree - - 89 r viewing angle (cr>10) white blue green red 0.613 gy 0.287 gx 0.065 by 0.144 bx 0.292 wy 0.279 wx ms 0.343 ry typ +0.03 0.640 typ -0.03 rx color coordinates [cie1931] 4,5 8 5 - g to g response time luminance variation 2 cd/m 2 - 500 400 l wh surface luminance, white note unit contrast ratio max typ min value symbol parameter www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 16 /32 lc420wu5 ver1.0 notes :1. contrast ratio(cr) is defined mathematica lly as : cr(contrast ratio) = maximum crn (n=1, 2, 3, 4, 5) surface luminance at position n with all white pixe ls crn = surface luminance at position n with all black pixe ls n = the position number(1, 2, 3, 4, 5). for more i nformation, see fig 2. 2. surface luminance are determined after the unit has been on and 30min after lighting the backlight in a dark environment at 25 2 c. surface luminance is the luminance value at cen ter 1-point across the lcd surface 50cm from the surfac e with all pixels displaying white. for more information see the fig. 2. 3. the variation in surface luminance , white is defined as : white(5p) = maximum(l on1 ,l on2 , l on3 , l on4 , l on5 ) / minimum(l on1 ,l on2 , l on3 , l on4 , l on5 ) where l on1 to l on5 are the luminance with all pixels displaying white at 5 locations . for more information, see the fig. 2. 4. response time is the time required for the displ ay to transition from g(n) to g(m) (rise time, tr r ) and from g(m) to g(n) (decay time, tr d ). for additional information see the fig. 3. (n product specification 17 /32 lc420wu5 ver1.0 fig. 3 response time response time is defined as the following figure an d shall be measured by switching the input signal f or gray(n) and gray(m). measuring point for surface luminance & measuring point for luminance variation. fig. 2 5 points for luminance measure a : h / 4 mm b : v / 4 mm @ h,v : active area h a v b gray(m) gray(n) t r r t r d 100 90 10 0 optical response n,m = black~white, n product specification 18 /32 lc420wu5 ver1.0 fig. 4 viewing angle dimension of viewing angle range normal y e = 0 , right = 180 , left = 270 , down = 90 , up www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 19 /32 lc420wu5 ver1.0 table 13 provides general mechanical characteristic s. 5. mechanical characteristics table 13. mechanical characteristics value item 523.26mm vertical 11.5 kg (typ.) , 12.5 kg (max.) weight 531.0 mm vertical 576.0 mm vertical 51.0 mm depth 930.24mm horizontal active display area 939.0 mm horizontal bezel area 983.0 mm horizontal outline dimension note : please refer to a mechanic drawing in terms of tolerance at the next page. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 20 /32 lc420wu5 ver1.0 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 21 /32 lc420wu5 ver1.0 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 22 /32 lc420wu5 ver1.0 6. reliability table 14. environment test condition ta= 40 c ,90%rh humidity condition operation 7 0 - 15,000 ft 0 - 40,000 ft altitude operating storage / shipment 8 shock level : 50grms waveform : half sine wave, 11ms direction : x, y, z one time each direction shock test (non-operating) 6 wave form : random vibration level : 1.0grms bandwidth : 10-300hz duration : x,y,z, 30 min one time each direction vibration test (non-operating) 5 ta= 0 c 240h low temperature operation test 4 ta= 50 c 50%rh 240h high temperature operation test 3 ta= -20 c 240h low temperature storage test 2 ta= 60 c 240h high temperature storage test 1 condition test item no. note : before and after reliability test, lcm sho uld be operated with normal function. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 23 /32 lc420wu5 ver1.0 7. international standards 7-1. safety a) ul 60065, 7 th edition, dated june 30, 2003, underwriters laborato ries, inc., standard for audio, video and similar electronic ap paratus. b) can/csa c22.2, no. 60065:03, canadian standards association, standard for audio, video and similar electronic ap paratus. c) iec60065:2001, 7 th edition cb-scheme and en 60065:2002, safety requirements for audio, video and similar el ectronic apparatus.. 7-2. emc a) ansi c63.4 methods of measurement of radio-nois e emissions from low-voltage electrical and electrical equipment in the range of 9khz to 40ghz. american national standards institute(ansi), 1992 b) cispr13 "limits and methods of measurement of r adio interference characteristics of sound and television broadcast receivers and associated e quipment" cispr22 "limits and methods of measurement of radi o interference characteristics of information technology equipment" international special commit tee on radio interference. c) en55013 "limits and methods of measurement of ra dio interference characteristics of sound and television broadcast receivers and associated equip ment" en55022 "limits and methods of measurement of radio interference characteristics of information technology equipment" european committee for elect ro technical standardization.(cenelec), 1988(including a1:2000) www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 24 /32 lc420wu5 ver1.0 8-1. designation of lot mark a) lot mark a b c d e f g h i j k l m a,b,c : size(inch) d : year e : month f : panel code g : factory code h : assembly code i,j,k,l,m : serial n o. note 1. year b) location of lot mark 2. month serial no. is printed on the label. the label is at tached to the backside of the lcd module. this is subject to change without prior notice. 8-2. packing form a) package quantity in one pallet : 12 pcs b) pallet size : 1140 mm x 990 mm x 810 mm b nov mark month a oct 6 jun 7 jul 8 aug 9 sep 4 apr 5 may c 4 2 1 dec mar feb jan 8. packing mark year 0 2010 6 2006 7 2007 8 2008 9 2009 4 2004 5 2005 3 2 1 2003 2002 2001 www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 25 /32 lc420wu5 ver1.0 please pay attention to the followings when you use this tft lcd module. 9-1. mounting precautions (1) you must mount a module using specified mountin g holes (details refer to the drawings). (2) you should consider the mounting structure so t hat uneven force (ex. twisted stress) is not applie d to the module. and the case on which a module is mounted s hould have sufficient strength so that external force is not transmitted directly to the module. (3) please attach the surface transparent protectiv e plate to the surface in order to protect the pola rizer. transparent protective plate should have sufficient strength in order to the resist external force. (4) you should adopt radiation structure to satisfy the temperature specification. (5) acetic acid type and chlorine type materials fo r the cover case are not desirable because the form er generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit b reak by electro-chemical reaction. (6) do not touch, push or rub the exposed polarizer s with glass, tweezers or anything harder than hb pencil lead. and please do not rub with dust clothe s with chemical treatment. do not touch the surface of polarizer for bare hand or greasy cloth.(some cosmetics are detrimental to the polarizer.) (7) when the surface becomes dusty, please wipe gen tly with absorbent cotton or other soft materials l ike chamois soaks with petroleum benzine. normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) wipe off saliva or water drops as soon as possi ble. their long time contact with polarizer causes deformations and color fading. (9) do not open the case because inside circuits do not have sufficient strength. 9-2. operating precautions 9. precautions (1) the spike noise causes the mis-operation of cir cuits. it should be lower than following voltage : v= 200mv(over and under shoot voltage) (2) response time depends on the temperature.(in lo wer temperature, it becomes longer.) (3) brightness depends on the temperature. (in lowe r temperature, it becomes lower.) and in lower temperature, response time(required ti me that brightness is stable after turned on) becomes longer (4) be careful for condensation at sudden temperatu re change.condensation makes damage to polarizer or electrical contacted parts. and after fading conden sation, smear or spot will occur. (5) when fixed patterns are displayed for a long ti me, remnant image is likely to occur. (6) module has high frequency circuits. sufficient suppression to the electromagnetic interference shal l be done by system manufacturers. grounding and shieldi ng methods may be important to minimized the interference. (7) please do not give any mechanical and/or acoust ical impact to lcm. otherwise, lcm cant be operated its full characteristics perfectly. (8) a screw which is fastened up the steels should be a machine screw. (if not, it can causes conductive particles and dea l lcm a fatal blow) (9) please do not set lcd on its edge. (10) it is recommended to avoid the signal cable an d conductive material over the inverter transformer for it can cause the abnormal display and temperatu re rising. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 26 /32 lc420wu5 ver1.0 since a module is composed of electronic circuits, it is not strong to electrostatic discharge. make c ertain that treatment persons are connected to ground through w rist band etc. and dont touch interface pin direct ly. 9-3. electrostatic discharge control strong light exposure causes degradation of polariz er and color filter. 9-4. precautions for strong light exposure when storing modules as spares for a long time, the following precautions are necessary. (1) store them in a dark place. do not expose the m odule to sunlight or fluorescent light. keep the te mperature between 5 c and 35 c at normal humidity. (2) the polarizer surface should not come in contac t with any other object. it is recommended that they be stored in the contai ner in which they were shipped. 9-5. storage 9-6. handling precautions for protection film (1) the protection film is attached to the bezel wi th a small masking tape . when the protection film is peeled off, static elec tricity is generated between the film and polarizer . this should be peeled off slowly and carefully by p eople who are electrically grounded and with well i on- blown equipment or in such a condition, etc. (2) when the module with protection film attached i s stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the p rotection film is peeled off. (3) you can remove the glue easily. when the glue r emains on the bezel surface or its vestige is recog nized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with norma l- hexane. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 27 /32 lc420wu5 ver1.0 r10/r20 r11/r21 r12/r22 r13/r23 r14/r24 r15/r25 r16/r26 r17/r27 g10/g20 g11/g21 g12/g22 g13/g23 g14/g24 g15/g25 g16/g26 g17/g27 b10/b20 b11/b21 b12/b22 b13/b23 b14/b24 b15/b25 b16/b26 b17/b27 hsync vsync data enable clock host system 24 bit ta1-ta1+ tb1-/tb1+ tc1-/tc1+ tclk1- tclk1+ td1-/td1+ ta2-/ta2+ tb2-/tb2+ tc2-/tc2+ tclk2- tclk2+ td2-/td2+ thc63lvd823 or compatible rxo0- rxo0+ rxo1- rxo1+ rxo2- rxo2+ rxoclk- rxoclk+ rxo3- rxo3+ rxe0- rxe0+ rxe1- rxe1+ rxe2- rxe2+ rxeclkin- rxeclkin+ rxe3- rxe3+ vesa / jeida dcr enable fi-r51s-hf timing controller lcd module ground 49 48 47 46 40 39 44 43 42 41 37 35 31 30 36 34 32 29 28 27 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 12 13 14 15 16 17 19 20 22 23 28 29 30 31 32 33 35 36 38 39 7 10 53/81 54/82 57/83 58/84 59/85 60/86 51/79 52/80 63/91 64/92 65/93 66/94 67/95 68/96 61/89 62/90 73/99 74/100 75/1 76/2 77/5 78/6 69/97 70/98 7 8 9 10 # appendix-i-1 required signal assignment for flat link (thine : t hc63lvd823) transmitter(pin7=l) notes: 1. the lcd module uses a 100 ohm( ? ) resistor between positive and negative lines of each receiver input. 2. refer to lvds transmitter data sheet for detail descriptions. (thc63lvd823 or compatible) 3. 7 means msb and 0 means lsb at r,g,b pixel dat a. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 28 /32 lc420wu5 ver1.0 r10/r20 r11/r21 r12/r22 r13/r23 r14/r24 r15/r25 r16/r26 r17/r27 g10/g20 g11/g21 g12/g22 g13/g23 g14/g24 g15/g25 g16/g26 g17/g27 b10/b20 b11/b21 b12/b22 b13/b23 b14/b24 b15/b25 b16/b26 b17/b27 hsync vsync data enable clock host system 24 bit thc63lvd823 or compatible 51/79 52/80 53/81 54/82 57/83 58/84 59/85 60/86 61/89 62/90 63/91 64/92 65/93 66/94 67/95 68/96 69/97 70/98 73/99 74/100 75/1 76/2 77/5 78/6 7 8 9 10 ta1-ta1+ tb1-/tb1+ tc1-/tc1+ tclk1- tclk1+ td1-/td1+ ta2-/ta2+ tb2-/tb2+ tc2-/tc2+ tclk2- tclk2+ td2-/td2+ rxo0- rxo0+ rxo1- rxo1+ rxo2- rxo2+ rxoclk- rxoclk+ rxo3- rxo3+ rxe0- rxe0+ rxe1- rxe1+ rxe2- rxe2+ rxeclkin- rxeclkin+ rxe3- rxe3+ vesa / jeida dcr enable fi-r51s-hf timing controller lcd module vcc 49 48 47 46 40 39 44 43 42 41 37 35 31 30 36 34 32 29 28 27 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 100 ? ?? ? 12 13 14 15 16 17 19 20 22 23 28 29 30 31 32 33 35 36 38 39 7 10 # appendix-i-2 required signal assignment for flat link (thine : t hc63lvd823) transmitter(pin7=h) notes: 1. the lcd module uses a 100 ohm( ? ) resistor between positive and negative lines of each receiver input. 2. refer to lvds transmitter data sheet for detail descriptions. (thc63lvd823 or compatible) 3. 7 means msb and 0 means lsb at r,g,b pixel dat a. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 29 /32 lc420wu5 ver1.0 # appendix-ii pallet assy steel band,clip 9 pp band 10 yupo 80g 100x100 label 11 paper angle,packing 8 paper 1140x990x130mm pallet 4 masking 20mmx50m tape 3 eps packing,top 6 eps packing,bottom 5 paper angle,post 7 42inch bag 2 lcd module 1 material description no. www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 30 /32 lc420wu5 ver1.0 # appendix 2 # appendix- iii lcm label 8 serial no. (see cas 24page for more information) 1 2 3 4 5 6 7 9 10 11 12 inch m assy factory code serial no. 13 month year model serial no. ul, tuv mark lpl logo us patent no. origin lc420wu5 (sl) (a2) www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 31 /32 lc420wu5 ver1.0 # appendix 3 # appendix- iv pallet label lc420wu5 sla2 12 pcs 001/01-01 made in korea xxxxx xxxxxxxx xxx xxx xxxx rohs verified www.datasheet.co.kr datasheet pdf - http://www..net/
product specification 32 /32 lc420wu5 ver1.0 circuit block diagram of lvds format selection pin asic (tcon) 50~100k ? ?? ? system side lcm side selector (pin 7) selector 1k ? ?? ? # appendix- v option pin circuit block diagram www.datasheet.co.kr datasheet pdf - http://www..net/

▲Up To Search▲

Price & Availability of LC420WU5-SLA2

	To Download LC420WU5-SLA2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .